We recommend allowing 2 weeks for the surface to fully cure and harden prior to damp-mopping or placing rugs/mats on the surface. Apply Polyx-Oil with a rag and sand it into the wood using wet-or-dry paper until you reach a pastelike consistency. For Natural (no colour change from raw wood) tint Polyx-Oil with Wood Wax Finish 3111 White at 3% for the base-coat, followed by a coat of clear (untinted) Polyx-Oil as a top-coat.Ĭure Period: Osmo Hardwax-Oil(s) like all floor finishes have a cure period. Do not exceed a ratio of 10 parts Polyx®-Oil 3054 to 1 part Wood Wax Finish.Įx. Tinting: Osmo Wood Wax Finish can also be used to lightly tint Polyx®-Oil 3054 up to a ratio of 10:1. Osmo has a full line of wood finishing and maintenance products starting from their line of hardwax oils like the popular Polyx-Oil 3054 for flooring and. Please consult OSMO technical support at 1-844-OSMOCAN prior to carrying out a third coat Third Coat: Usually a third coat is not required, however highly absorbent or dry timbers may appear to require a third coat. Allow for good ventilation whilst drying. Allow approximately 5-10 minutes for product to penetrate surface.Brush or roll the second coat thinly and evenly onto the floor.Second Coat: Roll or Brush a thin second coat Allow 8-10 hours drying time prior to proceeding to second coat.Easy application no need for a primer or sanding between coats, which saves time and money. Resistant to water and dirt, very durable and smooths wood surfaces. Do not remove excess product, this will absorb into the wood surface over the drying period Osmo Wood Wax Finish is a satin-matte wood finish which combines all the advantages of oils and waxes in one unique product.Brush or roll the product thinly and evenly onto the floor.Stir the Polyx®-Oil well and prior to use.Osmo Wood Wax Finish is not recommended for use on dense hardwoods such as Jarrah and Eucalypt, or timbers with a high oil and resin content such as Kwila/Merbau or Rosewood.First Coat: Apply one thin coat with an Osmo Floor Brush or Osmo Floor Roller. Suitable timbers include Pine, Kauri, Cedar, Oak, and Douglas Fir (Oregon). Also suitable for children’s toys, cots, bassinets and playpens etc. Wood Wax Finish is suitable for timber furniture such as shelving, doors, architraves, sarking and paneling. OSMOS PROCESS FOR WOOD PRESERVATION OSMOSE WOOD PRESERVING CO. Cleaning: Osmo Wash and Care should be used for general cleaning of Polyx treated floors. To finish, apply a very thin coat of clear Polyx Oil. After the first coat has dried, apply the second coat thinly and quickly. As a reminder, make sure that you're going back over your work piece with a clean finishing pad to remove any of the excess. On lighter coloured woods, apply thinly along the grain with a floor brush, spread well and work into the wood. Easy application - no need for sanding between coats, which saves time and money. Now, Osmo does require two coats, so you have to wait at least 8 to 10 hours before applying the second coat, and we're going to use the same exact steps as before. It penetrates deeply into the wood fibers to protect and nourish from within, giving your wood a natural, velvety finish that highlights the woods unique grain and character. Resistant to water and dirt, is wipe-proof and stain resistant. Osmo Polyx Oil Rapid is a high-quality, hard-wearing oil for wood surfaces. It is possible to create an almost infinite variation of naturally occurring colour shades to enhance the grain showing a gorgeous, natural colour tone or if you prefer a choice of intensive, bright or vivid colours - Wood Wax Finish is the product to give your interior wood a durable surface that adapts to the demands of life. Custom Timber Furniture Terms & ConditionsĬombining all the advantages of oils and waxes in one unique product.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |